A Step-by-Step Overview to Installing a Bath Tub
A Step-by-Step Overview to Installing a Bath Tub
Blog Article
They are making several good observations related to How to Install a Bathtub Yourself as a whole in this article directly below.
Mounting a tub isn't precisely rocket science, however it does require solid plumbing, carpentry, and also sometimes, tiling abilities. Changing an old bath tub with a brand-new one is additionally a reasonably hard task. If the old bathtub is conveniently obtainable, the job can relocate immediately; if you need to open up a wall surface to eliminate the old tub and position the brand-new bath tub, the job is a lot harder. In either situation, the task is within a residence handyman's abilities, although you will certainly need a helper to move out the old bathtub as well as set in the brand-new one. See to it you have qualified on your own for the task as well as are comfortable trying it. Instead of employing a professional to take control of a halfway-completed job, it is far better to think about using one prior to you start. Opportunities are you might need an expert plumber to make tube connections.
This short article will help you mount a brand-new tub in your restroom if you have currently acquired a brand-new bathtub as well as don't need to change the setup of your previous water pipelines.
Your tools and material list need to make up the following:
Removing Old Taps
If you need to replace old faucets with new ones as a part of your installation, then the first thing you need to do is detach the supply of water. After doing so, turn on the faucets to drain pipes any water remaining in the system. The procedure of eliminating the existing taps can be fairly troublesome due to the limited accessibility that is typically the case.
Make use of a container wrench (crowsfoot spanner) or a tap device to reverse the nut that connects the supply pipelines to the taps. Have a cloth all set for the staying water that will originate from the pipes. As soon as the supply pipelines have been gotten rid of, utilize the same device to loosen the nut that holds the faucets onto the bath/basin. You will require to stop the single faucets from turning throughout this process. As soon as the faucets have been eliminated, the holes in the bath/basin will need to be cleaned of any kind of old sealing substance.
Before going on to fit the new faucets, compare the pipeline connections on the old faucets to the new faucets. If the old taps are longer than the brand-new taps, after that a shank adapter is required for the brand-new taps to fit.
Suitable New Taps
If the tails of the brand-new taps are plastic, after that you will require a plastic adapter to avoid damage to the thread. One end of the adapter fits on the plastic tail of the tap and also the other end gives a connection to the current supply pipes.
If you need to fit a monobloc, after that you will call for decreasing couplers, which attaches the 10mm pipe of the monobloc to the common 15mm supply pipe.
Next, place the tap in the installing hole in the bath/basin making certain that the washers remain in area between the faucet and also the sink. Protect the faucet in place with the producer given backnut. When the faucet is securely in position, the supply pipelines can be connected to the tails of the taps. The faucets can either be connected by using corrugated copper piping or with regular faucet connectors. The previous kind should be linked to the faucet finishes first, tightening just by hand. The supply pipelines can later be linked to the various other end. Tighten up both ends with a spanner after both ends have been connected.
Setting up the Bath tub
Using the two wooden boards under its feet, position the tub in the needed placement. The wood boards are useful in uniformly spreading out the weight of the bath tub over the area of the boards instead of focusing all the weight onto 4 tiny factors.
The next goal is to guarantee that the bath tub is leveled all round. This can be attained by examining the spirit level and changing the feet on the tub until the spirit level checks out degree.
To mount taps, fit the bottom of the furthest versatile tap port to the suitable supply pipe by making a compression join; after that do the exact same for the other tap.
Switch on the supply of water and check all joints and brand-new pipework for leakages and also tighten them if essential. Load the bathtub and also check the overflow outlet and the normal outlet for leaks.
Finally, fix the bathroom paneling as defined in the supplier's user's manual. Tiling and securing around the tub should wait until the bath tub has actually been utilized at least when as this will certainly resolve it into its final placement.
Planning for the Setup
Firstly, the supporting structure provided with the bath should be fitted (if called for) according to the maker's directions. Next, fit the faucets or mixer to the tub. When fitting the faucet block, it is necessary to ensure that if the tap features a plastic washing machine, it is fitted between the bathroom as well as the taps. On a plastic bathroom, it is likewise sensible to fit a sustaining plate under the faucets unit to stop stress on the bathtub.
Fit the adaptable tap connectors to the bottom of both taps using 2 nuts as well as olives (in some cases provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and afterwards pass the electrical outlet through the hole in the bathroom. Use the nut provided by the manufacturer to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the adaptable overflow pipeline to the overflow outlet. Afterwards, screw the pipe to the overflow face which should be fitted inside the bathroom. Ensure you use every one of the supplied washing machines.
Connect the catch to the bottom of the waste outlet on the tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the catch to the electrical outlet. Link all-time low of the overflow tube in a similar manner.The bathroom ought to currently be ready to be suited its final placement.
Tiling Around the Tub
In the area where the bathroom meets the floor tile, it is required to secure the joins with a silicone rubber caulking. This is necessary as the fitting can relocate enough to split an inflexible seal, triggering the water to pass through the wall in between the bathroom and the tiling, bring about complications with moisture and also possible leakages to the ceiling listed below.
You can choose from a range of coloured sealers to assimilate your fixtures as well as installations. They are offered in tubes and also cartridges, and can securing spaces approximately a width of 3mm (1/8 inch). If you have a bigger void to fill, you can load it with twists of soaked newspaper or soft rope. Bear in mind to constantly fill the tub with water prior to securing, to allow for the motion experienced when the bathtub remains in use. The sealant can break rather very early if you do not think about this activity before securing.
Conversely, ceramic coving or quadrant tiles can be utilized to border the bath or shower tray. Plastic strips of coving, which are easy to use as well as reduce to dimension, are also quickly readily available on the market. It is recommended to fit the ceramic tiles utilizing waterproof or water-proof glue and also cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
We hope you enjoyed our article about How to Install a Bathtub. Thanks so much for finding the time to read our blog post. Enjoyed reading our blog? Please share it. Help somebody else discover it. Thanks for your time invested reading it.
Book A Free Estimate
Report this page